Hilfecenter
DE
FrançaisEnglishDeutschItalianoEspañolNederlands
Chargekeeper ↗
Startseite / Technische Konfiguration / Charging Station Diagnostics & Maintenance / Manufacturer error codes / Hager error codes

Hager error codes

Aktualisiert am 28. Oktober 2026
Dieser Artikel ist noch nicht auf Deutsch verfügbar. Es wird die English-Version angezeigt.
ocppdiagnosticshagererror codes

This page covers Hager witty charging stations: witty park (XEV6xx, XEV6xxC), witty park 2 (XVP222S, XVG222S), witty plus (XVL122…), witty pro, witty share (XEV1R22T2…) and witty XEV1Kxx. It details the codes the charging station can send to the supervision, then the lights and the display, which remain the main source of information on these stations.

Where to read the code: in Chargekeeper, charging station list, connector details, column
Information (or the in-progress sessions list, column Information). It shows
"OCPP code - vendor code - information". See Manufacturer error codes.

How Hager reports its errors

Hager publishes no list of OCPP vendor codes for its witty stations. On charging stations supervised by Chargekeeper, most witty stations send no vendor code: only the information field sometimes describes the error. When a code does arrive, it takes two forms:

  • a text code, for example CableFailure or WeldedContactFailure. These codes match the errors Hager documents in the diagnostic file of the witty XEV1Kxx ("Cable Failure", "CP Failure"…), sent without spaces ("Cable Failure" arrives as CableFailure). The information field may complete them (for example cable_32 or EV side disconnected);
  • a numeric code with an English label in the information field (for example Fuse fault). Hager does not document these codes: see the section "Codes seen on our charging stations".

Other faults can only be read on the station: lights, display (witty park 2), diagnosis tab of the web configurator (witty park, 2023 manual), "Live Debug" and "Logs" pages of the configurator (witty park 2, witty share Eichrecht) or the Diagnostics menu of the mobile app (witty plus, witty pro). Hager does not list the texts shown by these tools.

On the witty park (2023 manual), setting EV41 stops charging when the reactive current exceeds 2.5 A; the station then sends OCPP status SuspendedEVSE.

witty — text codes sent to the supervision

Errors documented by Hager for the diagnostic file of the witty XEV1Kxx ([Error] section).

Code Meaning What to do OCPP code
CableFailure Cable fault (cable coding resistor out of tolerance) Replace the cable Mode3Error
CPShortCircuitFailure Pilot (CP) line short circuit Replace the cable; if it persists, call Hager technical support Mode3Error, EVCommunicationError
Over Consumption Vehicle drew more current than allowed Unplug and retry —
Ventilation Error Vehicle requested ventilation Charge on another compatible station —
Load Shedding Failure Load shedding occurred too often Review load management or subscribed power —
CPFailure Pilot (CP) signal fault Replace the cable; if it persists, call Hager technical support EVCommunicationError
DC Current Failure DC fault current coming from the vehicle Refer the driver to the vehicle dealer —
WeldedContactFailure Welded contact on the contactor of socket 1 Send an electrician to replace the contactor OtherError
DC Sensor Failure DC leakage detection sensor faulty Send an electrician —

Codes seen on our charging stations, not documented by Hager

These codes were received from charging stations supervised by Chargekeeper but are not in the
manufacturer's public documentation. The label is the one sent by the charging station itself.

Code Label sent by the charger OCPP code
EV41 — OtherError
2 "EV41: Reactive current was detected, increasing mi" OtherError
63 "Fuse fault" OtherError
57 "Soft overcurrent" OtherError
19 "Proximity changed during charging process" OtherError
39 "Soft overcurrent" OtherError
99 "Stuck in the undefined logic state;Last state: Bas" OtherError

Lights and display

The light pattern depends on the model and, for some, on the product version. Start with the table of your model.

witty park XEV6xx — 2023 manual (rev. D)

On a fault the light is solid red and the error description is shown in the diagnosis tab of the station's web configurator.

Signal Meaning What to do
Red solid Station in fault; the exact cause is given in the diagnosis tab of the web configurator Read the diagnosis tab of the station configurator; for a selector fault, have a qualified electrician switch off, wait 15 s, set an allowed value and switch on; otherwise try another cable / vehicle before sending an electrician
Red solid 3 s + supply cut Welded contactor contact detected; supply cut through the MZ203 shunt-trip coil Send an electrician to check and replace the contactor
Red/white 3x then green RFID badge not accepted Check the badge in the CPMS or the local whitelist; retry with a valid badge
Off No power on the station Check the upstream circuit breaker and residual-current device

witty park XEV6xx — 2017 manuals

First generation: the number of red blinks gives the fault type. Depending on its board or firmware, a witty park follows this table or the previous one; Hager does not say which.

Signal Meaning What to do
Red blinking 1x Charging cable rejected: cable faulty or not supported Try another charging cable; if it persists with several cables, have the socket inspected
Red blinking 2x Pilot (CP) line shorted to earth — station and vehicle cannot communicate (IEC 61851 state E) Unplug and try another cable; if it persists, check the vehicle inlet and the station socket
Red blinking 3x Vehicle drew more current than the station allowed, four times in the same session Unplug and start a new session; if it repeats with the same vehicle, refer the driver to the vehicle maker
Red blinking 4x Vehicle requests a ventilated charging area (IEC 61851 state D); charging is refused Charge the vehicle on another compatible station
Red blinking 5x Load shedding triggered too often (four times in one session); the supply is too small for the demand Review the load-management settings or the subscribed power with the site owner
Red blinking 6x Abnormal pilot signal between station and vehicle Try another cable; if it persists, have the earth connection and the socket checked by an electrician
Red blinking fast RFID badge not accepted Check the badge is enabled in the CPMS or in the local whitelist; retry with a valid badge
Red solid Forbidden configuration: the maximum-current selector is on a value not allowed for this wiring, or a welded contactor contact was detected Have a qualified electrician switch off, wait 15 s, set the selector to an allowed value and switch on (green light expected); if the selector is correct, treat as a welded contactor and send an electrician
Red solid 3 s + supply cut Welded contactor contact detected; the station trips its supply through the MZ203 shunt-trip coil Do not re-arm repeatedly; send an electrician to check and replace the contactor
Red/blue blinking fast Station cannot reach the supervision (OCPP) server Check the station network link and the OCPP server URL / ChargePoint ID / credentials
Off No power on the station Check the upstream circuit breaker and residual-current device
Green/blue blinking slow Vehicle exceeded the allowed current (one to three times in the session); charging continues None; at the fourth occurrence the station stops (red blinking 3x)
Blue undulating Charging limited or paused by load management (power reduction, external stop signal, load shedding 1 to 3 times) None; normal behaviour

witty park 2 (XVP222S, XVG222S)

Error messages are shown on the station screen; Hager does not list them.

Signal Meaning What to do
Red solid Station faulty / critical error; charging not possible Switch the station off for 2 minutes to reset; read the message on the station screen; if it follows installation work, have the phase order checked
Red blinking Error in the charging station Follow the on-screen instructions
RFID reader red RFID card refused Check the card in the CPMS

witty plus and witty pro (XVL122…)

Hager documents only one generic fault state.

Signal Meaning What to do
Red solid Station faulty (critical error) Switch the station off for 2 minutes to clear the error; if it persists, check the app Diagnostics menu and contact Hager technical support
Red blinking RFID badge not valid Check the badge in the CPMS / station access control
Red blinking (dial on 7 or 9) Not a fault: output-contact test (dial on 7) or factory reset in progress (dial on 9) Have a qualified electrician power off, set the dial back to 0–6 (current setting) and power on

witty share XEV1R22T2x, witty XEV1K22T2x and XEV1K07T2x — 2023 guide

Hager states that the signalling varies with the product version. Several causes share the same blink count: the light alone does not identify the fault.

Signal Meaning What to do
Red blinking 1x Cable fault or interrupted pilot exchange with the vehicle Replace the charging cable
Red blinking 2x RFID card not recognised, or vehicle not recognised Retry; have the card enabled; replace the cable; if it persists, check connections and refer to the vehicle dealer
Red blinking 3x Vehicle over-consumption, ventilation/temperature issue, vehicle communication error, or (depending on version) DC fault current Unplug, ventilate if needed, retry; if it persists, refer to the vehicle dealer
Red blinking 8x DC fault current of 6 mA detected (on versions using 8 blinks for this fault) Refer the driver to the vehicle dealer
Red blinking 4x Local network problem (Ethernet/Wi-Fi) or communication error with the internal energy meter Check network cabling and that a DHCP router is present; use a compatible station
Red blinking 5x Charging interrupted: over-temperature, insufficient building supply, or Mode 2 socket protection tripped Remove the cause (cool down, reduce load, re-arm the Mode 2 circuit protection)
Red blinking 6x Station cannot establish a correct connection with the vehicle, or RFID reader / hardware failure Replace the cable; if it persists, contact the installer or Hager technical support
Red solid Critical error (e.g. RFID reader failure, defective or misconfigured hardware) Switch the station off for 2 minutes to reset; if it persists, send a qualified electrician / contact Hager technical support
Red pulsing Vehicle charging in emergency (degraded) mode Find and fix the cause; contact the vehicle dealer if needed
White blinking 2x Local network problem (Ethernet/Wi-Fi) or no link with the flow energy-management controller Check network connections and DHCP; reconnect the station to the flow controller

witty share Eichrecht (XEV1R22T2ER)

Signal Meaning What to do
Red blinking 1x Mode 3 socket cable fault (bad PP) or pilot short circuit (state E) Try another cable
Red blinking 2x RFID card rejected Check the card is enabled in the CPMS / whitelist
Red blinking 3x Vehicle over-consumption, ventilation request (state D), vehicle communication error or 6 mA DC fault current Unplug and retry; if it repeats with one vehicle, refer to the vehicle maker
Red blinking 4x No communication with the internal MID energy meter or the LSC metering capsule Power-cycle; if it persists, contact Hager technical support
Red blinking 5x Charging reduced or interrupted by high temperature, or Mode 2 socket protection open Let the unit cool; re-arm the Mode 2 socket protection
Red solid Critical error Switch the station off for 2 minutes to reset; have a qualified electrician check the selector position; if it persists, send an electrician (phase order, missing phase, hardware)
White blinking Local network link lost or not configured (Ethernet/Wi-Fi) Check the network configuration of the station
White solid (communication lost) Connection to the OCPP server lost Check the OCPP server URL, ChargePoint ID and credentials, and the network
FF Error shown on the calibration-law meter display: the charging station is not working Contact the station operator / Hager technical support

Other models: witty XEV1Kxx — 2021 manual

The blink count is also written in the station's diagnostic file (see the text codes above).

Signal Meaning What to do
Red solid Internal fault: meter link (TIC) fault, welded 40 A contactor, or faulty/disconnected DC leakage sensor Send an electrician to find and repair the cause
Red pulsing Charging in degraded mode, limited to 7 A single-phase / 13 A three-phase Have the meter link (TIC) checked by an electrician
Green blinking fast DC leakage above 6 mA detected from the vehicle; after three detections the station switches to red blinking 8x Refer the driver to the vehicle dealer
Red blinking 1x Charging cable faulty or not supported Replace the cable
Red blinking 2x Vehicle detection does not work Replace the cable; if it persists, check vehicle and station sockets, then call Hager technical support
Red blinking 3x Vehicle does not respect the current limit set by the station Unplug and retry; if it persists, call Hager technical support
Red blinking 4x Vehicle requires ventilation management, which this station does not provide Charge on another compatible station
Red blinking 5x Load shedding too frequent because the building supply is insufficient Suggest a TIC card upgrade (meter-based load management) or a higher subscription
Red blinking 6x Station does not receive a valid charge authorisation signal from the vehicle Replace the cable; if it persists, call Hager technical support
Red blinking 8x Vehicle generates a DC fault current that prevents charging Refer the driver to the vehicle dealer

Sources

Chargekeeper

Energie meistern. Laden vereinfachen.

© 2026 Chargekeeper — Hilfecenter